Issue 4 - June 2007
1
www.zetex.com
?Zetex Semiconductors plc 2007
ZXCT1032
High-side inrush controller and electronic fuse
Description
Ordering information
The ZXCT1032 is a high-side current monitor
that drives a PMOS or PNP transistor to
provide in-rush current limit and over-current
protection. The ZXCT1032 includes a high
accuracy high-side current monitor, a start-up
timer and a re-try inhibit timer.
The ZXCT1032 takes the voltage developed
across a current shunt resistor and compares
this with an externally set trip point. It works
in three modes:
" Linear soft-start
" Over-current detector
" Over-current disconnect/fuse
Linear soft-start
Upon power up the ZXCT1032 enters a linear
soft-start mode. During which the output
current ramps up from zero to a maximum
user defined trip point. The trip point is set by
the voltage on I
SET
pin and R
SENSE
.
The ramp rate is determined by capacitor C
T
.
The soft start ensures that capacitive loads are
smoothly charged without causing excessive
power supply startup transients.
Over-current detectior
When external capacitor CT has charged up
above the V
ISET
the ZXCT1032 switches from its
soft-start mode to its over-current detection
mode. During this mode the external MOSFET
will be fully enhanced reducing the its voltage
drop and power dissipation.
While in this mode the internal current monitor
continually checks the output current and
compares it to the trip-current level determined
by V
ISET
.
Over-current disconnect/fuse
If the trip current limit is exceeded at any time the
ZXCT1032 enters its Over-current disconnect
mode. The drive pin is driven high, turning the
pass MOSFET off; the flag output goes low
indicating a fault.
The drive and flag outputs are latched in these
states for a period determined by C
T
, V
ISET
and the
internally set discharge current (3礎 typical). After
C
T
has discharged to 80mV the ZXCT1032 will
restart into its linear soft-start mode.
The C
T
charge and discharge times have been
ratioed to so that the power dissipation in the
pass MOSFET should allow indefinite operation
in the event of a continuous load failure.
Pin 3 description:
Determines the load current trip level or
constant current level. ISET can be left open
circuit (internal 2.1V reference) or driven via a
DC voltage or 礐 PWM output. Its source
impedance is 50k.
Features
" Accurate high-side current sensing
" User defined and dynamically adjustable
trip current
" Load switch control
" Fault flag logic output
" User defined ramp and inhibit timers
" SO8 package
" Temperature range -40 to 85癈
Applications
" Electronic fuse
" Short circuit protected supply feed
" Hot swap
" Power over twisted pair
Order code
Pack
Part mark
Reel size
Tape width
Quantity per reel
ZXCT1032N8TA
SO8
1032
7
12mm
500
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZXCT1041E5TA
IC CURRENT MONITOR 1% SOT23-5
ZXCT1050E5TA
IC CURRENT MONITOR 3% SOT23-5
ZXCT1051E5TA
IC CURRENT MONITOR 1% SOT23-5
ZXCT1080E5TA
IC CURRENT MONITOR 3% SOT23-5
ZXCT1081E5TA
IC CURRENT MONITOR 3% SOT23-5
ZXCT1085E5TA
IC CURRENT MONITOR 3% SOT23-5
001-0001
ANTENNA 2.4GHZ DIPOLE 2DBI
001-0002
ANTENNA 900MHZ DIPOLE 2DBI
相关代理商/技术参数
ZXCT1032N8TA-CUT TAPE
制造商:DIODES 功能描述:ZXCT1032 Series 2.5 uA 9.5 to 21 V Controller and Electronic Fuse - SOIC-8
ZXCT1041
制造商:ZETEX 制造商全称:ZETEX 功能描述:Bidirectional precision high-side current monitor
ZXCT1041E5TA
功能描述:电流和电力监控器、调节器 Bi-Direct High Side RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
ZXCT1050
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Precision wide input range current monitor
ZXCT1050E5TA
功能描述:电流和电力监控器、调节器 Wide CMR Curr. Mon. RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
ZXCT1051
制造商:ZETEX 制造商全称:ZETEX 功能描述:Precision wide input range current monitor
ZXCT1051_0611
制造商:ZETEX 制造商全称:ZETEX 功能描述:Precision wide input range current monitor
ZXCT1051E5TA
功能描述:电流和电力监控器、调节器 Precision Wide Input RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel